SILENT KNIGHT 4720 Instrukcja Instalacji Strona 59
- Strona / 82
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Regency
®
Model 4724 Control Expander Installation Manual (P/N 150596-02, Rev. A) Revised 8/98
51
8.18 Default Options (Menu 17)
DEFAULT ALL?
If you select this option, all options will return to their factory-programmed default values.
WARNING! This will return all options to their factory-programmed default values.
8.19 Code 0 and Code 1
NOTE The secret codes for Codes 0 (installer's code) and Code 1 (main user's code) are programmed
in a separate menu and are NOT part of the 1 1 TEST menu structure. See Section 7.6 of this
manual for instructions on programming these codes.
Section 9: Using the Model 5540 Downloading Soft-
ware
The Model 5540 Downloading Software allows you to use a computer at a remote location to
reprogram options and perform other functions for a particular installation. For more specific
information, see the Model 5540 Downloading Software Operation Section Manual (P/N
150481) of the Model 4720 Installation Manual (P/N 150476).
NOTE Software Revision 3.1 is required of downloading.
■ Initial Downloads—During factory programming, the Answer Ring option was
selected (Dialer, Menu 5). Once the panel is installed, the downloading computer can
call it to download new program data or request status information from the panel.
After 10 rings (the factory programmed value for the # RINGS option), the panel will
answer the call and downloading will begin.
■ Subsequent Downloads—If the Answer Ring option is still enabled the computer can
call the panel as described above. Downloading can also be initiated from a touchpad at
the installation location, by pressing 4 TEST followed by Code 0 or Code 1.
During uploading or downloading, the touchpad LCD will display “UP/DOWNLOAD.”
During the downloading of options to the EEPROM (electrically erasable programmable
read-only memory) the LCD will also display address numbers. Downloading of all
options takes approximately 12 minutes. Downloading cannot take place while the system
is in alarm.
WARNING! During downloading, the system will NOT respond to alarms.
9.1 Starting and Ending
1. If you have just powered up the computer, enter the word MODEM at the DOS prompt.
OR- If this has been done since the computer was turned on, enter the word PANEL at the
DOS prompt.
2. Then enter your user name and password when the prompts direct you to do so.
3. The Panel Interface Menu will appear on the screen.
4. To exit the Model 5540 downloading program, press ESC as many times as necessary,
until you see a prompt asking you if you want to leave the program.
- Installation Manual 1
- 2266 Second Street N orth 2
- FCC Notices 3
- Table of Contents 4
- List of Figures 7
- List of Tables 8
- Section 1: Introduction 9
- Section 2: UL Requirements 10
- Section 3: Installation 11
- MODEL 4720 12
- 3.2 Zone Expanders 13
- 3.3.1 Installation 14
- Section 4: Touchpad Operation 15
- 4.2 Touchpad Functions 16
- Section 5: Area Control 17
- 5.2 Area Assignments 18
- 7.1 Entering Program Mode 19
- 7.3 Programming the Options 19
- 7.4 Correcting Errors 20
- 7.5 Entering Text 20
- Table 2: Text and Characters 21
- 7.6 Programming Secret Codes 22
- 8457G15A.DS4 23
- 8.1 Time Windows (Menu 0) 24
- 8.2 Access (Menu 1) 25
- 8.3 Holidays (Menu 2) 27
- 8.5 System (Menu 4) 27
- Selection Default Mode 28
- “Exceptional” 31
- 8.6 Dialer (Menu 5) 35
- 8.7 Zone Options (Menu 6) 36
- Selection Loop Response Time 37
- TYPE#1:FIRE 39
- LOCATION#1 39
- SIL ALM#1:NO (Silent Alarm) 39
- REP. DLY#1:NO 39
- Table 7: Zone Types 39
- 8.8 Accounts (Menu 7) 40
- 8.9 Intercom (Menu 8) 42
- 8.10 Window Groups (Menu 9) 43
- 8.11 Messages (Menu 10) 43
- 8.12 Timers (Menu 11) 45
- Selection Day 46
- 8.13 Key Options (Menu 12) 47
- 8.14 Key Zones (Menu 13) 48
- 8.15 Area Options (Menu 14) 50
- 8.17.2 Program Operations 51
- Additional 52
- Info Needed 52
- 8.17.3 Changing the Program 56
- Inserting a New Statement 56
- Table 15: Default I/O Program 58
- 8.19 Code 0 and Code 1 59
- 9.1 Starting and Ending 59
- 9.2 Viewing Status 60
- 9.3 Uploading Event Memory 61
- 9.4 Programming Procedure 61
- Figure 5: Auxiliary Devices 62
- Table 16: Logical Operators 63
- Table 19: Output Designations 65
- Data Type Function 67
- Table 21: Zone Groups 69
- 11.1.1 Open/Close Groups 70
- 11.1.2 Exception Reporting 70
- 11.1.3 Open/Close Trouble 70
- 11.1.4 Auto Open/Close 70
- 11.2.1 New Programming Tools 70
- 11.3 New Options 71
- 11.4 Operational Changes 72
- Built-In Programmer 73
- Arm Delay 73
- Door Contact 73
- Entry Zones 73
- ONE YEAR LIMITED WARRANTY 74
- Numerics 75
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa SILENT KNIGHT 4720
(48 strony)Acer 3650 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Notatniki Acer 3650.
Dostarczamy 1 pdf podręczników Acer 3650 do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Komentarze do niniejszej Instrukcji